Projectile points are tools that were hafted as points in arrows.
There are many types e.g.: single-edged points, transverse points, tanged points, bifacial points.
- 2 Unifacial points
- 3 Bifacial points
- 4 Point types
- 5 Tanged points
- 6 References
Bifacially retouched points are projectile points that are retouched on both surfaces, often with invasive retouch covering most of both surfaces. They are divided into types by shape. e.g.. bifacial leaf-shaped point, bifacial triangular point,bifacial lanceolate point. They may be tanged or have barbs, or both, as in a bifacial barbed and tanged point.
Single-edged points are projectile points that have two retouched edges. The edges are formed by abrupt retouch and are usually modified along one full edge and are diverging from the base to an edge. The shortest retouched edge must be < 60 % of the longest retouched side. (Helskog et al.1976:25).
Transverse points are projectile points that do not form a point but have a straight or angled "cutting" edge. They are often made from a medial section of a blade or bladelet so that the "cutting" edge is the original edge of the blank. i.e. they are oriented transversely to the axis of percussion.
The transverse point is made from the ventral side of the blade. The bulb of force is removed and the knapper works his way into the blade until an oblique, convex breakeage occur on both sides. Thus the point is equipped with one broad edge on one of the sides of the blade and a thin shaft end on the other. The point is finally shaped with a pressure flaker, in part by pressure and in part by using the hammerstone as an anvil and the pressure flaker as a hammer. The width of the transverse point should correspond to the witdh of the arrow shaft (Bay og Staal 2003:26-74).
Tanged points are projectile points that have a tang at one end to facilitate hafting. A tang is made by retouching one, or more usually both edges, in order to create a projection that is thinner than the width of the blank. This projection is then fitted into the arrow shaft.
Ahrensburgian points are small tanged points with a retouched tang in the distal end of a blade. The points are normally obliquely retouched (Vang Petersen 1993). Ahrensburgian points are characteristic of the late paleolithic Ahrensburg culture.
Bromme-/Lyngby points are large tanged points made on big blades. The tang is manufactured in the proximal end of the blade where the bulb of force often is intact (Vang Petersen 1993). Bromme-/Lyngby points can be interpreted as spear points.
A-points are made on a blade with a retouched tang in the proximal end and a natural point in its distal end. A-points are further grouped into the categories A1-A3 based on the direction of the retouch from the dorsal or ventral side of the point. A-points are normally viewed as Neolithic.
Tanged point - A1
are projectile points that are made from naturally pointed blade blanks that have no, or little, retouch except for the tang which is created by direct retouch.
Tanged point - A2
are projectile points. They are most common in the production of tangs for projectile points, particularly in the A2 and B types of Neolithic typology (Helskog et al.1976:26).
Tanged point - A2
are projectile points. They are most common in the production of tangs for projectile points, particularly in the A2 and B types of Neolithic typology (Helskog et al.1976:26). Tanged points- A2 have alternate retouch position
Tanged point - A3
are simple tanged points made on blades. Only the tang and occasionally the point are retouched. The tang is made by inverse abrupt retouch.
A-points are normally attributed to the Early Neolithic.
Barbed and tanged point
Barbed and tanged points are bifacial projectile points
that are retouched on both surfaces with barbs and tang.
Bifacial leaf-shaped point
Bifacial leaf-shaped points are bifacial projectile points that are retouched on both surfaces and shaped like a leaf
Bifacial triangular point
Bifacial triangular points are bifacial projectile points that are retouched on both surfaces and triangular in shape.
Bifacial lanceolate point
Bifacial lanceolate points are bifacial projectile points that are retouched on both surfaces and lanceolate i.e. elongated leaf shaped.
- Helskog, K., Indrelid, S., and Mikkelsen, E. 1976 Morfologisk klassifisering av slåtte steinartefakter. Særtykk fra Universitetets Oldsaksamlings årbok 1972-1974. Cite error: Invalid
<ref>tag; name "Helskog_1976" defined multiple times with different content Cite error: Invalid
<ref>tag; name "Helskog_1976" defined multiple times with different content