Difference between revisions of "User Manual - NIM Gate and Delay Generator"

From mn/safe/nukwik
Jump to: navigation, search
(Instructions for use as gating pulse)
 
(2 intermediate revisions by the same user not shown)
Line 19: Line 19:
 
A typical G&amp;D generator similar to the one used for the laboratory exercise is displayed to the right.<br>  
 
A typical G&amp;D generator similar to the one used for the laboratory exercise is displayed to the right.<br>  
  
This manual was written as part of a student lab exercise in the KJM-FYS&nbsp;5920 course at the University of Oslo in the autumn 2010.
+
==== Instructions for use as gating signal<br>  ====
 
 
Quick links:&nbsp;[[KJM-FYS 5920 Lab Exercise 4 - Student Written Equipment User Manuals|KJM-FYS&nbsp;5920 Lab Exercise 4]] | [[KJM-FYS 5920 @ UiO - Autumn 2010|KJM-FYS 5920 Course]]
 
 
 
Main author (student): Alexander
 
 
 
Co-author (student):
 
 
 
Lab supervisor:&nbsp;[mailto:hildethn@student.matnat.uio.no Hilde-Therese Nyhus] (PhD-student)
 
 
 
Responsible teacher:&nbsp;Prof. [mailto:j.p.omtvedt@kjemi.uio.no Jon Petter Omtvedt]
 
 
 
==== User Manual for NIM Gate and Delay Generator  ====
 
 
 
[[Image:Lab4GandDgen.png|right]]
 
 
 
The Gate and Delay Generator is a device that generates variable logic pulses when incoming pulses triggers it. The output pulses can in turn be used as, for example, a gate for linear pulses from a spectroscopy amplifier (SA) entering an ADC/MCA.<br>
 
 
 
A typical G&amp;D generator similar to the one used for the laboratory exercise is displayed to the right.<br>
 
 
 
==== Instructions for use as gating pulse<br>  ====
 
  
 
In order to use the G&amp;D generator as a gate device for linear pulses from a SA, proceed as follows:<br>  
 
In order to use the G&amp;D generator as a gate device for linear pulses from a SA, proceed as follows:<br>  

Latest revision as of 08:31, 22 November 2010

This manual was written as part of a student lab exercise in the KJM-FYS 5920 course at the University of Oslo in the autumn 2010.

Quick links: KJM-FYS 5920 Lab Exercise 4 | KJM-FYS 5920 Course

Main author (student): Alexander

Co-author (student):

Lab supervisor: Hilde-Therese Nyhus (PhD-student)

Responsible teacher: Prof. Jon Petter Omtvedt

User Manual for NIM Gate and Delay Generator

Lab4GandDgen.png

The Gate and Delay Generator is a device that generates variable logic pulses when incoming pulses triggers it. The output pulses can in turn be used as, for example, a gate for linear pulses from a spectroscopy amplifier (SA) entering an ADC/MCA.

A typical G&D generator similar to the one used for the laboratory exercise is displayed to the right.

Instructions for use as gating signal

In order to use the G&D generator as a gate device for linear pulses from a SA, proceed as follows:

  • Connect the output from a single channel analyser to the input on the Gate and Delay (G&D) generator.
  • View the output pulses from the spectroscopy amplifier (SA) and the G&D generator on a suitable oscilloscope.
  • Using the dial for delay on the G&D generator, adjust the logical output pulse so that the duration is equal to (or just a bit larger than) the positive component of the SA pulse.
  • Using the dial (or front-panel screwdriver control) for amplitude on the G&D generator, make the logical pulse larger in amplitude than the SA pulse.
  • Connect the output port on the G&D generator to the ADC Gate port on the MCA.


Lab4gatedelaysko.PNG


In the above figure, the pink signal is the final, adjusted output pulse from the G&D generator, and the yellow signal is the linear pulse from the Spectroscopy amplifier. If the logical G&D generator pulse is to be used as a gate, the linear pulse from the SA would need to be delayed so the logical pulse can encompass the linear pulse.